first commit
This commit is contained in:
STP
259
etc_org/default/tlp
Normal file
259
etc_org/default/tlp
Normal file
@ -0,0 +1,259 @@
|
||||
# ------------------------------------------------------------------------------
|
||||
# tlp - Parameters for power save
|
||||
# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html
|
||||
|
||||
# Hint: some features are disabled by default, remove the leading # to enable
|
||||
# them.
|
||||
|
||||
# Set to 0 to disable, 1 to enable TLP.
|
||||
TLP_ENABLE=0
|
||||
|
||||
# Operation mode when no power supply can be detected: AC, BAT
|
||||
# Concerns some desktop and embedded hardware only.
|
||||
TLP_DEFAULT_MODE=AC
|
||||
|
||||
# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
|
||||
# Non-zero value enables, zero disables laptop mode.
|
||||
DISK_IDLE_SECS_ON_AC=0
|
||||
DISK_IDLE_SECS_ON_BAT=2
|
||||
|
||||
# Dirty page values (timeouts in secs).
|
||||
MAX_LOST_WORK_SECS_ON_AC=15
|
||||
MAX_LOST_WORK_SECS_ON_BAT=60
|
||||
|
||||
# Hint: CPU parameters below are disabled by default, remove the leading #
|
||||
# to enable them, otherwise kernel default values are used.
|
||||
|
||||
# Select a CPU frequency scaling governor:
|
||||
# ondemand, powersave, performance, conservative
|
||||
# Intel Core i processor with intel_pstate driver:
|
||||
# powersave, performance
|
||||
# Important:
|
||||
# You *must* disable your distribution's governor settings or conflicts will
|
||||
# occur. ondemand is sufficient for *almost all* workloads, you should know
|
||||
# what you're doing!
|
||||
#CPU_SCALING_GOVERNOR_ON_AC=ondemand
|
||||
#CPU_SCALING_GOVERNOR_ON_BAT=ondemand
|
||||
|
||||
# Set the min/max frequency available for the scaling governor.
|
||||
# Possible values strongly depend on your CPU. For available frequencies see
|
||||
# tlp-stat output, Section "+++ Processor".
|
||||
#CPU_SCALING_MIN_FREQ_ON_AC=0
|
||||
#CPU_SCALING_MAX_FREQ_ON_AC=0
|
||||
#CPU_SCALING_MIN_FREQ_ON_BAT=0
|
||||
#CPU_SCALING_MAX_FREQ_ON_BAT=0
|
||||
|
||||
# Set Intel P-state performance: 0..100 (%)
|
||||
# Limit the max/min P-state to control the power dissipation of the CPU.
|
||||
# Values are stated as a percentage of the available performance.
|
||||
# Requires an Intel Core i processor with intel_pstate driver.
|
||||
#CPU_MIN_PERF_ON_AC=0
|
||||
#CPU_MAX_PERF_ON_AC=100
|
||||
#CPU_MIN_PERF_ON_BAT=0
|
||||
#CPU_MAX_PERF_ON_BAT=30
|
||||
|
||||
# Set the CPU "turbo boost" feature: 0=disable, 1=allow
|
||||
# Requires an Intel Core i processor.
|
||||
# Important:
|
||||
# - This may conflict with your distribution's governor settings
|
||||
# - A value of 1 does *not* activate boosting, it just allows it
|
||||
#CPU_BOOST_ON_AC=1
|
||||
#CPU_BOOST_ON_BAT=0
|
||||
|
||||
# Minimize number of used CPU cores/hyper-threads under light load conditions
|
||||
SCHED_POWERSAVE_ON_AC=0
|
||||
SCHED_POWERSAVE_ON_BAT=1
|
||||
|
||||
# Kernel NMI Watchdog:
|
||||
# 0=disable (default, saves power), 1=enable (for kernel debugging only)
|
||||
NMI_WATCHDOG=0
|
||||
|
||||
# Change CPU voltages aka "undervolting" - Kernel with PHC patch required
|
||||
# Frequency voltage pairs are written to:
|
||||
# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
|
||||
# CAUTION: only use this, if you thoroughly understand what you are doing!
|
||||
#PHC_CONTROLS="F:V F:V F:V F:V"
|
||||
|
||||
# Set CPU performance versus energy savings policy:
|
||||
# performance, normal, powersave
|
||||
# Requires kernel module msr and x86_energy_perf_policy from linux-tools
|
||||
ENERGY_PERF_POLICY_ON_AC=performance
|
||||
ENERGY_PERF_POLICY_ON_BAT=powersave
|
||||
|
||||
# Hard disk devices; separate multiple devices with spaces (default: sda).
|
||||
# Devices can be specified by disk ID also (lookup with: tlp diskid).
|
||||
DISK_DEVICES="sda sdb"
|
||||
|
||||
# Hard disk advanced power management level: 1..254, 255 (max saving, min, off)
|
||||
# Levels 1..127 may spin down the disk; 255 allowable on most drives.
|
||||
# Separate values for multiple devices with spaces.
|
||||
DISK_APM_LEVEL_ON_AC="254 254"
|
||||
DISK_APM_LEVEL_ON_BAT="128 128"
|
||||
|
||||
# Hard disk spin down timeout:
|
||||
# 0: spin down disabled
|
||||
# 1..240: timeouts from 5s to 20min (in units of 5s)
|
||||
# 241..251: timeouts from 30min to 5.5 hours (in units of 30min)
|
||||
# See 'man hdparm' for details.
|
||||
#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
|
||||
#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"
|
||||
|
||||
# Select IO scheduler for the disk devices: noop, deadline, cfq (Default: cfq);
|
||||
# Separate values for multiple devices with spaces.
|
||||
#DISK_IOSCHED="cfq cfq"
|
||||
|
||||
# SATA aggressive link power management (ALPM):
|
||||
# min_power, medium_power, max_performance
|
||||
SATA_LINKPWR_ON_AC=max_performance
|
||||
SATA_LINKPWR_ON_BAT=min_power
|
||||
|
||||
# PCI Express Active State Power Management (PCIe ASPM):
|
||||
# default, performance, powersave
|
||||
PCIE_ASPM_ON_AC=performance
|
||||
PCIE_ASPM_ON_BAT=powersave
|
||||
|
||||
# Radeon graphics clock speed (profile method): low, mid, high, auto, default;
|
||||
# auto = mid on BAT, high on AC; default = use hardware defaults.
|
||||
# (Kernel >= 2.6.35 only, open-source radeon driver explicitly)
|
||||
RADEON_POWER_PROFILE_ON_AC=high
|
||||
RADEON_POWER_PROFILE_ON_BAT=low
|
||||
|
||||
# Radeon dynamic power management method (DPM): battery, performance
|
||||
# (Kernel >= 3.11 only, requires boot option radeon.dpm=1)
|
||||
RADEON_DPM_STATE_ON_AC=performance
|
||||
RADEON_DPM_STATE_ON_BAT=battery
|
||||
|
||||
# Radeon DPM performance level: auto, low, high; auto is recommended.
|
||||
RADEON_DPM_PERF_LEVEL_ON_AC=auto
|
||||
RADEON_DPM_PERF_LEVEL_ON_BAT=auto
|
||||
|
||||
# WiFi power saving mode: 1=disable, 5=enable; not supported by all adapters.
|
||||
WIFI_PWR_ON_AC=1
|
||||
WIFI_PWR_ON_BAT=5
|
||||
|
||||
# Disable wake on LAN: Y/N
|
||||
WOL_DISABLE=Y
|
||||
|
||||
# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
|
||||
# A value of 0 disables, >=1 enables power save.
|
||||
SOUND_POWER_SAVE_ON_AC=0
|
||||
SOUND_POWER_SAVE_ON_BAT=1
|
||||
|
||||
# Disable controller too (HDA only): Y/N
|
||||
SOUND_POWER_SAVE_CONTROLLER=Y
|
||||
|
||||
# Set to 1 to power off optical drive in UltraBay/MediaBay when running on
|
||||
# battery. A value of 0 disables this feature (Default).
|
||||
# Drive can be powered on again by releasing (and reinserting) the eject lever
|
||||
# or by pressing the disc eject button on newer models.
|
||||
# Note: an UltraBay/MediaBay hard disk is never powered off.
|
||||
BAY_POWEROFF_ON_BAT=0
|
||||
# Optical drive device to power off (default sr0).
|
||||
BAY_DEVICE="sr0"
|
||||
|
||||
# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable
|
||||
RUNTIME_PM_ON_AC=on
|
||||
RUNTIME_PM_ON_BAT=auto
|
||||
|
||||
# Runtime PM for *all* PCI(e) bus devices, except blacklisted ones:
|
||||
# 0=disable, 1=enable
|
||||
RUNTIME_PM_ALL=1
|
||||
|
||||
# Exclude PCI(e) device adresses the following list from Runtime PM
|
||||
# (separate with spaces). Use lspci to get the adresses (1st column).
|
||||
#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"
|
||||
|
||||
# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM
|
||||
# (should prevent accidential power on of hybrid graphics' discrete part).
|
||||
# Default is "radeon nouveau"; use "" to disable the feature completely.
|
||||
# Separate multiple drivers with spaces.
|
||||
RUNTIME_PM_DRIVER_BLACKLIST="radeon nouveau"
|
||||
|
||||
# Set to 0 to disable, 1 to enable USB autosuspend feature.
|
||||
USB_AUTOSUSPEND=1
|
||||
|
||||
# Exclude listed devices from USB autosuspend (separate with spaces).
|
||||
# Use lsusb to get the ids.
|
||||
# Note: input devices (usbhid) are excluded automatically (see below)
|
||||
#USB_BLACKLIST="1111:2222 3333:4444"
|
||||
|
||||
# WWAN devices are excluded from USB autosuspend:
|
||||
# 0=do not exclude / 1=exclude
|
||||
USB_BLACKLIST_WWAN=1
|
||||
|
||||
# Include listed devices into USB autosuspend even if already excluded
|
||||
# by the driver or WWAN blacklists above (separate with spaces).
|
||||
# Use lsusb to get the ids.
|
||||
#USB_WHITELIST="1111:2222 3333:4444"
|
||||
|
||||
# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
|
||||
# (workaround for USB devices that cause shutdown problems).
|
||||
#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1
|
||||
|
||||
# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
|
||||
# on system startup: 0=disable, 1=enable.
|
||||
# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
|
||||
# are ignored when this is enabled!
|
||||
RESTORE_DEVICE_STATE_ON_STARTUP=0
|
||||
|
||||
# Radio devices to disable on startup: bluetooth, wifi, wwan.
|
||||
# Separate multiple devices with spaces.
|
||||
#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"
|
||||
|
||||
# Radio devices to enable on startup: bluetooth, wifi, wwan.
|
||||
# Separate multiple devices with spaces.
|
||||
#DEVICES_TO_ENABLE_ON_STARTUP="wifi"
|
||||
|
||||
# Radio devices to disable on shutdown: bluetooth, wifi, wwan
|
||||
# (workaround for devices that are blocking shutdown).
|
||||
#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
|
||||
|
||||
# Radio devices to enable on shutdown: bluetooth, wifi, wwan
|
||||
# (to prevent other operating systems from missing radios).
|
||||
#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"
|
||||
|
||||
# Radio devices to enable on AC: bluetooth, wifi, wwan
|
||||
#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"
|
||||
|
||||
# Radio devices to disable on battery: bluetooth, wifi, wwan
|
||||
#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"
|
||||
|
||||
# Radio devices to disable on battery when not in use (not connected):
|
||||
# bluetooth, wifi, wwan
|
||||
#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
|
||||
|
||||
# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
|
||||
# required). Charging starts when the remaining capacity falls below the
|
||||
# START_CHARGE_TRESH value and stops when exceeding the STOP_CHARGE_TRESH value.
|
||||
# Main / Internal battery (values in %)
|
||||
#START_CHARGE_THRESH_BAT0=75
|
||||
#STOP_CHARGE_THRESH_BAT0=80
|
||||
# Ultrabay / Slice / Replaceable battery (values in %)
|
||||
#START_CHARGE_THRESH_BAT1=75
|
||||
#STOP_CHARGE_THRESH_BAT1=80
|
||||
|
||||
# ------------------------------------------------------------------------------
|
||||
# tlp-rdw - Parameters for the radio device wizard
|
||||
# Possible devices: bluetooth, wifi, wwan
|
||||
|
||||
# Hints:
|
||||
# - Parameters are disabled by default, remove the leading # to enable them.
|
||||
# - Separate multiple radio devices with spaces.
|
||||
|
||||
# Radio devices to disable on connect.
|
||||
#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
|
||||
#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
|
||||
#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
|
||||
|
||||
# Radio devices to enable on disconnect.
|
||||
#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
|
||||
#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
|
||||
#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
|
||||
|
||||
# Radio devices to enable/disable when docked.
|
||||
#DEVICES_TO_ENABLE_ON_DOCK=""
|
||||
#DEVICES_TO_DISABLE_ON_DOCK=""
|
||||
|
||||
# Radio devices to enable/disable when undocked.
|
||||
#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
|
||||
#DEVICES_TO_DISABLE_ON_UNDOCK=""
|
||||
Reference in New Issue
Block a user